yorkshire_spam Posted February 6, 2016 Share Posted February 6, 2016 Out of idle curiosity, what do you recon the limits are in terms of torque / hp for a standard 2000 diff? (and driveshafts) Quote Link to comment Share on other sites More sharing options...
Greeks Posted February 6, 2016 Share Posted February 6, 2016 About 20 bhp less than the least powerful variant Quote Link to comment Share on other sites More sharing options...
Nick Jones Posted February 6, 2016 Share Posted February 6, 2016 Certainly OK for 150 bhp / 160 lb/ft. Probably ok for 180 bhp / 200lb/ft.They usually die of lubrication failure (all leaked out or never changed) rather than outright breakage in Triumph engined cars. All bets off for imported V8s.....Nick Quote Link to comment Share on other sites More sharing options...
yorkshire_spam Posted February 6, 2016 Author Share Posted February 6, 2016 So 148 hp/243 lb·ft is gonna be right on the limit (or well over it it torque terms)Hmmmm Quote Link to comment Share on other sites More sharing options...
Ridgetone Triumph Posted February 6, 2016 Share Posted February 6, 2016 It will last for ever if you treat it properly, 10minutes if you don't.....Been there done that. You can also put 500hp power through one too, but driven carefully Quote Link to comment Share on other sites More sharing options...
Nick Jones Posted February 6, 2016 Share Posted February 6, 2016 Remember that the torque the diff sees is the engine torque multiplied by the gear ratio.So, considering my previous PI, which made 160 lb/ft at the flywheel, in first gear the diff would see 160 x 3.28 = 524.8 lb/ft. The driveshafts have it worse, as for them it is multiplied by the diff ratio too, so for the PI, 525 x 3.45 = 1810 lb/ft. All this without factoring shock loads due to things like dropping the clutch at 5000 rpm, loss and sudden regain of traction and similar.Goes some way to explaining why things last much better if you don't hoof it too hard in the lowest gears. Some modern cars actual have the torque limited by the engine ECU when in the lower gears.Nick Quote Link to comment Share on other sites More sharing options...
Jonny-Jimbo Posted February 8, 2016 Share Posted February 8, 2016 Not even just super-moderns - my mum had a diseasel turbo 306 from the mid-90's and that was torque limited on 1st to stop it (I guess) either blowing the clutch or shafts etc. Quote Link to comment Share on other sites More sharing options...
Encom Posted February 15, 2016 Share Posted February 15, 2016 Rip it out and whack in a Nissan long nose R200, good for 500hp Quote Link to comment Share on other sites More sharing options...
josh18 Posted February 15, 2016 Share Posted February 15, 2016 Hey Encom, have you got more pics of that install? It's on my list of things to do to mine. I'd like to see how you go about attaching the diff to the sub frame. Also has anyone used a subaru r160 diff? They are cheap, plentiful and much newer.Sorry about the thread hijackJosh Quote Link to comment Share on other sites More sharing options...
Nick Jones Posted February 15, 2016 Share Posted February 15, 2016 Doubt the R160 is any stronger than the original Triumph offering and the tallest ratio is 3.54. R200 is a much better choice. Alternatively look at BMW E30 and E36 compact where the rear clip can be transferred complete.Nick Quote Link to comment Share on other sites More sharing options...
yorkshire_spam Posted February 15, 2016 Author Share Posted February 15, 2016 The engine I have in mind is a Beemer, so I was wondering if it should be engine+gearbox conversion OR engine+gearbox+diff. Sounds like all 3 might be the "best" option. Quote Link to comment Share on other sites More sharing options...
Clive Posted February 15, 2016 Share Posted February 15, 2016 Quoted from Nick Jones Doubt the R160 is any stronger than the original Triumph offering and the tallest ratio is 3.54. R200 is a much better choice. Alternatively look at BMW E30 and E36 compact where the rear clip can be transferred complete.Nick Just had an R160 apart for a bit of ratio-changing.It turns out some have 4 sunwheels in the diff (the Viscous LSD with stepped splines on one shaft) and the later ones have 2 sunwheels. The diff. and CWP are all pretty meaty, though I suspect it may have its limit around 250bhp (more than enough for me!)But yes, for the effort and if enough space, use the bigger version. Quote Link to comment Share on other sites More sharing options...
StagNL Posted February 15, 2016 Share Posted February 15, 2016 I have a Subaru R160 in my Stag. It may be newer but the design goes way back to the Datsun 1600 510. There is a guy who races a Datsun 510 in the States with an output of a tad over 200bhp. If a Subaru R160 holds up with that during 10 years of harsh use on the race track, then it will be fine for my Stag. Ratio is 3.70:1 which is the same as the Stag original diff. The LSD types are more hard to come by and really only available in special edition models such as the Impreza WRX. Mine was from a Forrester.The R160 didn't just slot in though, I had to whack a dent in the rear crossmember box section where the rear diff mounting studs go through as the Subaru diff breather would foul there.If I need a new diff, I would consider the R200 as I am expecting a power increase once EFI is fitted.I have some photos on Flickr. Just need to get the proper link when I get home. Give me a few hours..... The mounting to the subframe is better than original as there is no separate nose piece that can break off.Julian Quote Link to comment Share on other sites More sharing options...
StagNL Posted February 15, 2016 Share Posted February 15, 2016 Here are the pics of my conversion: https://www.flickr.com/photos/12619047@N04/albums/72157620689843079Julian Quote Link to comment Share on other sites More sharing options...
Jonny-Jimbo Posted February 15, 2016 Share Posted February 15, 2016 If anyone needs one I have a BMW E30 propshaft I was about to chuck on ebay, but may be of use to anyone considering a BMW diff swap. Quote Link to comment Share on other sites More sharing options...
josh18 Posted February 16, 2016 Share Posted February 16, 2016 Thanks for the info guys.Nick I was most keen on the R160 because they are so plentiful and can easily be got with a proper LSD, eg WRX. I hear you about the strength, but I more want this diff as a cheaper way of going LSD. Plus if I break it another one is only 300 bucks or so. The beemer diffs are much less common here and dearer, plus look to me to be a lot harder to install.Cheers Quote Link to comment Share on other sites More sharing options...
StagNL Posted February 16, 2016 Share Posted February 16, 2016 If a R160 can put up with the power of a Subaru WRX, then I expect most Triumphs won't break them either. You have to be putting out well over 200bhp to get one go bang I reckon. Oh, and high torque. But still....Julian Quote Link to comment Share on other sites More sharing options...
josh18 Posted February 17, 2016 Share Posted February 17, 2016 Yeah that was what I was thinking too. Although Rex's are 4x4 so the power the diff sees is half there would be plenty around with 400 odd HP so yeah I reckon 200 in RWD should be OK. Cheers Quote Link to comment Share on other sites More sharing options...
Jonny-Jimbo Posted February 17, 2016 Share Posted February 17, 2016 Quoted from josh18 Yeah that was what I was thinking too. Although Rex's are 4x4 so the power the diff sees is half there would be plenty around with 400 odd HP so yeah I reckon 200 in RWD should be OK. Cheers Not always - some Imprezas are 50:50, but some are 60:40 or even 45:55... Unless you know what the diff came from you may not know what it originally had... however, even so I agree, that if the Diff can put up with the abuse these cars tend to get, then they'll live in a Triumph quite happily. Quote Link to comment Share on other sites More sharing options...
josh18 Posted February 17, 2016 Share Posted February 17, 2016 Another plus to the R160 is they come in pretty similar ratios as the trump. Quote Link to comment Share on other sites More sharing options...
iggy Posted February 19, 2016 Share Posted February 19, 2016 hi what model car does a R200 nissan diff come from and do any of you guys no the ratio options of these diffs thanks Quote Link to comment Share on other sites More sharing options...
Clive Posted February 19, 2016 Share Posted February 19, 2016 skylines, 200sx, 280Z and 300Zsome subarus too.Massively strong, as in pretty much unbreakable (you would need over 500bhp to have a chance of damaging one)R180 hugely strong too for most of us. R160 must be good for well over 200bhp Quote Link to comment Share on other sites More sharing options...
Encom Posted February 20, 2016 Share Posted February 20, 2016 The R160 is a great diff, I've run them in my Vitesse's and the Subaru guys thrash the nuts off them. It's only with some serious horse power do you actually need the likes of the R180 or R200. I just happen to have a R200 longnose kicking around at the time, and I'm running a RB25 in the car (non-turbo) so shouldn't stress the diff at all. With Triumph power levels it would be a walk in the park.The other point with the R160, is the early ones are come from the likes of the Datsun 180B; hence with the use of the Tri-Dat UJ's and the 180B half shafts its a pretty straight forward swap.Anyway here are some pic's of a R200 longnose in the saloon K Frame; Quote Link to comment Share on other sites More sharing options...
Encom Posted February 20, 2016 Share Posted February 20, 2016 Quoted from StagNL Here are the pics of my conversion: https://www.flickr.com/photos/12619047@N04/albums/72157620689843079Julian Sounds like there is a market for a batch of those adapter plates for the outputs shafts Quote Link to comment Share on other sites More sharing options...
josh18 Posted February 20, 2016 Share Posted February 20, 2016 Encom that looks great! Your set up looks a lot simpler than I have seen before. Are the brackets you mounted the diff onto cut down angle iron?Those pics are definitely going into the memory bank! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.